If you are looking forward to making colloidal silver with the help of a colloidal silver generator then you have come to the right place. below we will be discussing how you can make colloidal silver using a colloidal silver generator for the best results. if you are looking for a good production then you need to know the right voltage. If you are wondering it can be made at home, then you are right. Colloidal silver can be made at home too using a colloidal silver generator but one should maintain a low voltage for the best results.
It is advised to use the voltage of 30 volts for the best results. this is because the cathodes are the cleanest at this prescribed voltage offering the best results.
You are reading: Best voltage for making colloidal silver
Best voltage for making colloidal silver
![Different CBD Types and Cat Treats for Pets 7 How To Make Colloidal Silver At Home](https://ecis2016.org/wp-content/uploads/2021/10/How-To-Make-Colloidal-Silver-At-Home-1024x593.jpg)
Read also : Colloidal Silver Soap
When starting the process, it is advised to opt for 36 volts as it is the best voltage for making colloidal silver. This can be gained by using four batteries of 9 volts each or three batteries of 12 volts each for the best results. you are required to hold the silver anodes in a good way to get the best results.
Though higher voltages when used provides better results it is always advised to use low voltages as it makes the quality of the colloidal silver much better. This way the pure silver particles will come out well.
How to make colloidal silver at home
Colloidal silver can now be made at home by using the process of electrolysis for the best results. for this process, the requirements are distilled water, 99.9% silver two rods, alligator clips, 9-volt batteries and electrical wires. ensure to use the highest quality of silver electrodes to get a high-quality colloidal silver solution.
![Different CBD Types and Cat Treats for Pets 8 How To Make Colloidal Silver At Home 2](https://ecis2016.org/wp-content/uploads/2021/10/How-To-Make-Colloidal-Silver-At-Home-2-1024x612.jpg)
Preparation of colloidal silver
- The distilled water should be poured into the mason jar up till the lid shown for the best results.
- There are two holes in the plastic sheet. This is the place where the silver rods have to be placed.
- Once done the rods are required to be immersed in the water which is distilled.
- The silver rods should be connected to the wires using alligator clips. Once done connect them to the batteries.
- Once all the above is done it is time for electrolysis process which will take 3 to 4 hours for the best results.
- After the duration, you can disconnect the batteries and then take the rods out.
- Use coffee filter and using a funnel place it. This funnel should be put into the spray bottle that consist of glass that are tinted for the best results. Once done you can put the solution in the funnel.
- This coffee filter is able to catch any particles that are large in size.
- Once done it is advised to close the spray bottle tightly and then the cannabis plant needs to be sprayed lightly.
- Spray bottle requires to be placed in cool place.
Read also : Different CBD Types and Cat Treats for Pets
One fact to know is that colloidal silver has no expiry dates allowing you to use it for several years. If you are facing any trouble during the process or believe the results will not come accurate as desired then you can opt to watch some videos that show how to get this process done the right way.
Mentioned below are some of the precautionary actions that you should take when using 9-volt batteries:
- When you are connecting the wires to the battery ensure you connect the red cable initially followed by the black cable for the best results.
- While removing start with the black wire first and then the red wire.
- During the process, the positive and the negative batteries are situated very close to one another. ensure you tape them properly as it may cause a fire.
- Generally, the ends of the batteries are tiny so use an alligator clip at the end of the wires. This way they are going to stay on the battery. You can also opt to use electrical tapes to tape the alligator clips for the best results.
Conclusion
Mentioned above is the process of making colloidal silver at home. taking reference to the points mentioned above you can make colloidal silver at home. ensure you follow all the steps cautiously for the best results as a tiny difference can cause severe effects not giving you the desired results.
Source: https://ecis2016.org
Category: Scientific Information